Nitrogen is the polite gas of industry: inert, dry, always available from a membrane or PSA generator – but almost never at the pressure the application wants. Generators deliver 6-10 bar; laser cutters want 20-30, accumulators 90-150, test rigs 200 and more. The bridge between those two numbers is a nitrogen boosting system, and sizing one correctly is mostly about understanding three numbers: ratio, flow and drive-air consumption.
Where Boosted Nitrogen Earns Its Keep
- Accumulator and cylinder charging – hydraulic accumulators and N2 bottles routinely need 100-200 bar, far beyond any generator.
- Laser cutting assist gas – high-pressure nitrogen gives oxide-free edges on stainless and aluminium; boosting lets a low-pressure generator feed a 30 bar cutting head.
- Pressure and leak testing – inert, dry gas is the preferred test medium for components that must not see moisture, from valves to heat exchangers.
- Injection moulding and extrusion – internal gas-assist processes need steady medium-pressure nitrogen on demand.
How the Booster Works
The workhorse is the air-driven pressure amplifier: a large pneumatic piston drives a small high-pressure piston, so outlet pressure equals drive pressure multiplied by the area ratio – and the booster stalls and seals itself at the set pressure, consuming drive air only while actually pumping. That self-regulating behaviour is the quiet advantage over motor-driven compressors: no pressure switches, no unloaded running, no electricity near the gas.
For typical plant duties, an integrated gas booster system – booster, control panel, inlet regulation and safety valves on one skid – is simpler to own than assembling components, because the engineering decisions below have already been made. Single pumps such as the A16 series gas booster pump or the single-drive single-acting gas booster pump A32Q suit OEM integration and compact stations. The full range is on the gas booster pump category page.
Sizing Step 1 – Pressure Ratio
Rule one: the ratio must cover your worst case, not your average case. If the generator sags to 6 bar on a hot day and the accumulator needs 150 bar, a 20:1 unit is the minimum, not a 15:1. Rule two: staging is normal – two single-acting stages in series reach ratios no single stage should attempt, and the interstage cooler keeps the gas dry and the seals happy.
Sizing Step 2 – Flow at Pressure
Booster flow falls as outlet pressure rises, and published curves assume generous drive-air supply. Size for the time budget you actually care about: charging a 50-litre accumulator from 10 to 150 bar is a flow question with an answer in cubic metres per minute – state the task and the deadline, and the pump size follows. Undersized boosters do not fail; they just make every charging task twice as slow as promised.
Sizing Step 3 – Drive Air and Duty Cycle
Drive-air consumption is the hidden running cost – typically 1.5 to 2.5 cubic metres of shop air per cubic metre of gas delivered at high ratios. Check that your compressor has this headroom, especially if the booster runs alongside the plant’s normal demand. Air-driven boosters tolerate intermittent duty and stall at pressure without damage, which makes them ideal for charging tasks that sit idle between uses.
Frequently Asked Questions
Does boosting affect nitrogen purity?
Air-driven boosters with proper seals keep purity essentially unchanged – there is no combustion and no lubricant in the gas path on oil-free designs. Specifying oil-free construction matters where purity is certified, such as laser cutting and laboratory supply.
Can one system serve several applications?
Yes, with a pressure regulator and good manifold design on the outlet side. The booster should be sized for the highest pressure duty; lower-pressure users simply take gas through their regulator.
Why not just buy a high-pressure nitrogen compressor?
For continuous large flows, a compressor wins. For intermittent charging, testing and top-ups – the majority of plant applications – the air-driven booster is cheaper to buy, quieter, electrically isolated from the gas, and effectively maintenance-light because it stalls rather than idles.
BONOR engineers nitrogen boosting systems from single pumps to automated skids with full control panels. Send us your gas, inlet pressure and target pressure/flow, and we will size the unit and quote within days.